While I'm glad to see the OP got a good minimax solution at the end, it seems like the article missed clarifying one of the key points: error waveforms over a specified interval are critical, and if you don't see the characteristic minimax-like wiggle, you're wasting easy opportunity for improvement.
Taylor series in general are a poor choice, and Pade approximants of Taylor series are equally poor. If you're going to use Pade approximants, they should be of the original function.
Chebyshev polynomials cos(n arcos(x)) provide one of the proofs that every continuous function f:[0,1]->R can be uniformly approximated by polynomial functions. Bernstein polynomials provide a shorter proof, but perhaps not the best numerical method: https://en.wikipedia.org/wiki/Bernstein_polynomial#See_also
To be accurate, this is originally from Hastings 1955, Princeton
"APPROXIMATIONS FOR DIGITAL COMPUTERS BY CECIL HASTINGS", page 159-163, there are actually multiple versions of the approximation with different constants used. So the original work was done with the goal of being performant for computers of the 1950's.
Then the famous Abramowitz and Stegun guys put that in formula 4.4.45 with permission, then the nvidia CG library wrote some code that was based upon the formula, likely with some optimizations.
In general, I find that minimax approximation is an underappreciated tool, especially the quite simple Remez algorithm to generate an optimal polynomial approximation [0]. With some modifications, you can adapt it to optimize for either absolute or relative error within an interval, or even come up with rational-function approximations. (Though unfortunately, many presentations of the algorithm use overly-simple forms of sample point selection that can break down on nontrivial input curves, especially if they contain small oscillations.)
They teach a lot of Taylor/Maclaurin series in Math classes (and trig functions are sometimes called "CORDIC" which is an old method too) but these are not used much in actual FPUs and libraries. Maybe we should update the curricula so people know better ways.
Taylor series makes a lot more sense in a math class, right? It is straightforward and (just for example), when you are thinking about whether or not a series converges in the limit, why care about the quality of the approximation after a set number of steps?
Perhaps, but at least I find it very simple for the optimality properties it gives: there is no inherent need to say, "I know that better parameters likely exist, but the algorithm to find them would be hopelessly expensive," as is the case in many forms of minimax optimization.
Ideally either one is just a library call to generate the coefficients. Remez can get into trouble near the endpoints of the interval for asin and require a little bit of manual intervention, however.
> This amazing snippet of code was languishing in the docs of dead software, which in turn the original formula was scrawled away in a math textbook from the 60s.
was kind of telling for me. I have some background in this sort of work (and long ago concluded that there was pretty much nothing you can do to improve on existing code, unless either you have some new specific hardware or domain constraint, or you're just looking for something quick-n-dirty for whatever reason, or are willing to invest research-paper levels of time and effort) and to think that someone would call Abramowitz and Stegun "a math textbook from the 60s" is kind of funny. It's got a similar level of importance to its field as Knuth's Art of Computer Programming or stuff like that. It's not an obscure text. Yeah, you might forget what all is in it if you don't use it often, but you'd go "oh, of course that would be in there, wouldn't it...."
These are books that my uni courses never had me read. I'm a little shocked at times at how my degree program skimped on some of the more famous texts.
It is not a textbook, it is an extremely dense reference manual, so that honestly makes sense.
In physics grad school, professors would occasionally allude to it, and textbooks would cite it ... pretty often. So it's a thing anyone with postgraduate physics education should know exists, but you wouldn't ever be assigned it.
> After all of the above work and that talk in mind, I decided to ask an LLM.
Impressive that an LLM managed to produce the answer from a 7 year old stack overflow answer all on its own! [1] This would have been the first search result for “fast asin” before this article was published.
Interesting aeticle. A few years back I implemented a bunch of maths primitives, including trig functions, using Taylor sequences etc, to see how it was done. An interesting challenge, even at the elementary level I was working at.
So this article got me wondering how much accuracy is needed before computing a series beats pre-computed lookup tables and interpolation. Anyone got any relevant experience to share?
Not directly related, but if you are reaching for sin, cos, asin, acos, atan and their relatives to handle rotation, you may save yourself a lot of trouble by representing angle not as a scalar but as (i) a cos, sin tuple or (ii) equivalently as a complex numbers.
You may then get away with simple algebra and square roots. A runtime such as Python would do a lot of that transparently.
Isn't the faster approach SIMD [edit: or GPU]? A 1.05x to 1.90x speedup is great. A 16x speedup is better!
They could be orthogonal improvements, but if I were prioritizing, I'd go for SIMD first.
I searched for asin on Intel's intrinsics guide. They have a AVX-512 instrinsic `_mm512_asin_ps` but it says "sequence" rather than single-instruction. Presumably the actual sequence they use is in some header file somewhere, but I don't know off-hand where to look, so I don't know how it compares to a SIMDified version of `fast_asin_cg`.
I don’t know much about raytracing but it’s probably tricky to orchestrate all those asin calls so that the input and output memory is aligned and contiguous. My uneducated intuition is that there’s little regularity as to which pixels will take which branches and will end up requiring which asin calls, but I might be wrong.
Instead of an `_objects`, I might try for a `_spheres`, `_boxes`, etc. (Or just `_lists` still using the virtual dispatch but for each list, rather than each object.) The `asin` seems to be used just for spheres. Within my `Spheres::closest_hit` (note plural), I'd work to SIMDify it. (I'd try to SIMDify the others too of course but apparently not with `asin`.) I think it's doable: https://github.com/define-private-public/PSRayTracing/blob/8...
I don't know much about ray tracers either (having only written a super-naive one back in college) but this is the general technique used to speed up games, I believe. Besides enabling SIMD, it's more cache-efficient and minimizes dispatch overhead.
edit: there's also stuff that you can hoist in this impl. Restructuring as SoA isn't strictly necessary to do that, but it might make it more obvious and natural. As an example, this `ray_dir.length_squared()` is the same for the whole list. You'd notice that when iterating over the spheres. https://github.com/define-private-public/PSRayTracing/blob/8...
When I was working on this project, I was trying to restrict myself to the architecture of the original Ray Tracing in One Weekend book series. I am aware that things are not as SIMD friendly and that becomes a major bottle neck. While I am confident that an architectural change could yield a massive performance boost, it's something I don't want to spend my time on.
I think it's also more fun sometimes to take existing systems and to try to optimize them given whatever constraints exist. I've had to do that a lot in my day job already.
I don't do much float work but I don't think there is a single regular sine instruction only old x87 float stack ones.
I was curious what "sequence" would end up being but my compiler is too old for that intrinsic. Even godbolt didn't help for gcc or clang but it did reveal that icc produced a call https://godbolt.org/z/a3EsKK4aY
If you click libraries on godbolt, it's pulling in a bunch, including multiple SIMD libraries. You might have to fiddle with the libraries or build locally.
It appears that the real lesson here was to lean quite a bit more on theory than a programmer's usual roll-your-own heuristic would suggest.
A fantastic amount of collective human thought has been dedicated to function approximations in the last century; Taylor methods are over 200 years old and unlikely to come close to state-of-the-art.
The 4% improvement doesn't seem like it's worth the effort.
On a general note, instructions like division and square root are roughly equal to trig functions in cycle count on modern CPUs. So, replacing one with the other will not confer much benefit, as evidenced from the results. They're all typically implemented using LUTs, and it's hard to beat the performance of an optimized LUT, which is basically a multiplexer connected to some dedicated memory cells in hardware.
You'd be surprised how it actually is worth the effort, even just a 1% improvement. If you have the time, this is a great talk to listen to: https://www.youtube.com/watch?v=kPR8h4-qZdk
For a little toy ray tracer, it is pretty measly. But for a larger corporation (with a professional project) a 4% speed improvement can mean MASSIVE cost savings.
Some of these tiny improvements can also have a cascading effect. Imagining finding a +4%, a +2% somewhere else, +3% in neighboring code, and a bunch of +1%s here and there. Eventually you'll have built up something that is 15-20% faster. Down the road you'll come across those optimizations which can yield the big results too (e.g. the +25%).
It's a cool talk, but the relevance to the present problem escapes me.
If you're alluding to gcc vs fbstring's performance (circa 15:43), then the performance improvement is not because fbstring is faster/simpler, but due to a foundational gcc design decision to always use the heap for string variables. Also, at around 16:40, the speaker concedes that gcc's simpler size() implementation runs significantly faster (3x faster at 0.3 ns) when the test conditions are different.
Presumably the poster meant polynomial approximations of trigonometric functions not instructions for trigonometric functions, which are missing in most CPUs, though many GPUs have such instructions.
x86-64 had instructions for the exponential and logarithmic functions in Xeon Phi, but those instructions have been removed in Skylake Server and the later Intel or AMD CPUs with AVX-512 support.
However, instructions for trigonometric functions have no longer been added after Intel 80387, and those of 8087 and 80387 are deprecated.
Not required. ATAN and SQRTS(S|D) are sufficient, the half-angle approach in the article is the recommended way.
> People have gotten PhDs for smaller optimizations. I know. I've worked with them.
I understand the can, not sure about the should. Not trying to be snarky, we just seem to be producing PhDs with the slimmest of justifications. The bar needs to be higher.
> I understand the can, not sure about the should. Not trying to be snarky, we just seem to be producing PhDs with the slimmest of justifications. The bar needs to be higher.
I couldn't disagree more. Sure, making a 4% faster asin isn't going to change the world, but if it makes all callers a teensy bit faster, multiplied by the number of callers using it, then it adds up. Imagine the savings for a hyperscaler if they managed to made a more common instruction 4% faster.
> The 4% improvement doesn't seem like it's worth the effort.
I've spent the past few months improving the performance of some work thing by ~8% and the fun I've been having reminds me of the nineties, when I tried to squeeze every last % of performance out of the 3D graphics engine that I wrote as a hobby.
Does anyone knows the resources for the algos used in the HW implementations of math functions? I mean the algos inside the CPUs and GPUs. How they make a tradeoff between transistor number, power consumption, cycles, which algos allow this.
Microbenchmarks. A LUT will win many of them but you pessimise the rest of the code. So unless a significant (read: 20+%) portion of your code goes into the LUT, there isn't that much point to bother. For almost any pure calculation without I/O, it's better to do the arithmetic than to do memory access.
Locality within the LUT matters too: if you know you're looking up identical or nearby-enough values to benefit from caching, an LUT can be more of a win. You only pay the cache cost for the portion you actually touch at runtime.
I could imagine some graphics workloads tend compute asin() repeatedly with nearby input values. But I'd guess the locality isn't local enough to matter, only eight double precision floats fit in a cache line.
By interpolating between values you can get excellent results with LUTs much smaller than 32KB. Will it be faster than the computation from op, that I don't know.
I experimented a bit with the code. Various tables with different datatypes. There is enough noise from the Monte Carlo to not make a difference if you use smaller data types than double or float. Even dropping interpolation worked fine, and got the speed to be on par with the best in the article, but not faster.
Does your benchmark use sequential or randomly ordered inputs? That would make a substantial difference with an LUT, I would think. But I'm guessing. Maybe 32K is so small it doesn't matter (if almost all of the LUT sits in the cache and is never displaced).
> if you use smaller data types than double or float. Even dropping interpolation worked fine,
That's kinda tautological isn't it? Of course reduced precision is acceptable where reduced precision is acceptable... I guess I'm assuming double precision was used for a good reason, it often isn't :)
I didnt inspect the rest of the code but I guess the table is fetched from L2 on every call?
I think the L1 data cache is flooded by other stuff going on all the time.
About dropping the interpolation: Yes you are right of course. I was thinking about the speed. No noticable speed improvement by dropping interpolation. The asin calls are only a small fraction of everything.
I'm very skeptical you wouldn't get perceptible visual artifacts if you rounded the trig functions to 4096 linear approximations. But I'd be happy to be proven wrong :)
We love to leave faster functions languishing in library code. The basis for Q3A’s fast inverse square root had been sitting in fdlibm since 1986, on the net since 1993: https://www.netlib.org/fdlibm/e_sqrt.c
Funny enough that fdlimb implementation of asin() did come up in my research. I believe it might have been more performant in the past. But taking a quick scan of `e_asin.c`, I see it doing something similar to the Cg asin() implementation (but with more terms and more multiplications, which my guess is that it's slower). I think I see it also taking more branches (which could also lead to more of a slowdown).
While I'm glad to see the OP got a good minimax solution at the end, it seems like the article missed clarifying one of the key points: error waveforms over a specified interval are critical, and if you don't see the characteristic minimax-like wiggle, you're wasting easy opportunity for improvement.
Taylor series in general are a poor choice, and Pade approximants of Taylor series are equally poor. If you're going to use Pade approximants, they should be of the original function.
I prefer Chebyshev approximation: https://www.embeddedrelated.com/showarticle/152.php which is often close enough to the more complicated Remez algorithm.
Chebyshev polynomials cos(n arcos(x)) provide one of the proofs that every continuous function f:[0,1]->R can be uniformly approximated by polynomial functions. Bernstein polynomials provide a shorter proof, but perhaps not the best numerical method: https://en.wikipedia.org/wiki/Bernstein_polynomial#See_also
To be accurate, this is originally from Hastings 1955, Princeton "APPROXIMATIONS FOR DIGITAL COMPUTERS BY CECIL HASTINGS", page 159-163, there are actually multiple versions of the approximation with different constants used. So the original work was done with the goal of being performant for computers of the 1950's. Then the famous Abramowitz and Stegun guys put that in formula 4.4.45 with permission, then the nvidia CG library wrote some code that was based upon the formula, likely with some optimizations.
In general, I find that minimax approximation is an underappreciated tool, especially the quite simple Remez algorithm to generate an optimal polynomial approximation [0]. With some modifications, you can adapt it to optimize for either absolute or relative error within an interval, or even come up with rational-function approximations. (Though unfortunately, many presentations of the algorithm use overly-simple forms of sample point selection that can break down on nontrivial input curves, especially if they contain small oscillations.)
[0] https://en.wikipedia.org/wiki/Remez_algorithm
They teach a lot of Taylor/Maclaurin series in Math classes (and trig functions are sometimes called "CORDIC" which is an old method too) but these are not used much in actual FPUs and libraries. Maybe we should update the curricula so people know better ways.
Taylor series makes a lot more sense in a math class, right? It is straightforward and (just for example), when you are thinking about whether or not a series converges in the limit, why care about the quality of the approximation after a set number of steps?
Not sure I would call Remez "simple"... it's all relative; I prefer Chebyshev approximation which is simpler than Remez.
Perhaps, but at least I find it very simple for the optimality properties it gives: there is no inherent need to say, "I know that better parameters likely exist, but the algorithm to find them would be hopelessly expensive," as is the case in many forms of minimax optimization.
Ideally either one is just a library call to generate the coefficients. Remez can get into trouble near the endpoints of the interval for asin and require a little bit of manual intervention, however.
This line:
> This amazing snippet of code was languishing in the docs of dead software, which in turn the original formula was scrawled away in a math textbook from the 60s.
was kind of telling for me. I have some background in this sort of work (and long ago concluded that there was pretty much nothing you can do to improve on existing code, unless either you have some new specific hardware or domain constraint, or you're just looking for something quick-n-dirty for whatever reason, or are willing to invest research-paper levels of time and effort) and to think that someone would call Abramowitz and Stegun "a math textbook from the 60s" is kind of funny. It's got a similar level of importance to its field as Knuth's Art of Computer Programming or stuff like that. It's not an obscure text. Yeah, you might forget what all is in it if you don't use it often, but you'd go "oh, of course that would be in there, wouldn't it...."
Abramowitz/Stegun has been updated 2010 and resides now here: https://dlmf.nist.gov/
These are books that my uni courses never had me read. I'm a little shocked at times at how my degree program skimped on some of the more famous texts.
It is not a textbook, it is an extremely dense reference manual, so that honestly makes sense.
In physics grad school, professors would occasionally allude to it, and textbooks would cite it ... pretty often. So it's a thing anyone with postgraduate physics education should know exists, but you wouldn't ever be assigned it.
I'm pretty sure it's not faster, but it was fun to write:
Courtesy of evil floating point bithacks.That could do with some subtitles.
https://en.wikipedia.org/wiki/Fast_inverse_square_root
> floating point bithacks
The forbidden magic
You brought Zalgo. I blame this decade on you.
// what the fuck
> float asinine(float x) {
FTFY :P
> After all of the above work and that talk in mind, I decided to ask an LLM.
Impressive that an LLM managed to produce the answer from a 7 year old stack overflow answer all on its own! [1] This would have been the first search result for “fast asin” before this article was published.
[1]: https://stackoverflow.com/a/26030435
I did see that, but isn't the vast majority of that page talking about acos() instead?
Interesting aeticle. A few years back I implemented a bunch of maths primitives, including trig functions, using Taylor sequences etc, to see how it was done. An interesting challenge, even at the elementary level I was working at.
So this article got me wondering how much accuracy is needed before computing a series beats pre-computed lookup tables and interpolation. Anyone got any relevant experience to share?
How much accuracy does ray tracing require?
Not directly related, but if you are reaching for sin, cos, asin, acos, atan and their relatives to handle rotation, you may save yourself a lot of trouble by representing angle not as a scalar but as (i) a cos, sin tuple or (ii) equivalently as a complex numbers.
You may then get away with simple algebra and square roots. A runtime such as Python would do a lot of that transparently.
Isn't the faster approach SIMD [edit: or GPU]? A 1.05x to 1.90x speedup is great. A 16x speedup is better!
They could be orthogonal improvements, but if I were prioritizing, I'd go for SIMD first.
I searched for asin on Intel's intrinsics guide. They have a AVX-512 instrinsic `_mm512_asin_ps` but it says "sequence" rather than single-instruction. Presumably the actual sequence they use is in some header file somewhere, but I don't know off-hand where to look, so I don't know how it compares to a SIMDified version of `fast_asin_cg`.
https://www.intel.com/content/www/us/en/docs/intrinsics-guid...
I don’t know much about raytracing but it’s probably tricky to orchestrate all those asin calls so that the input and output memory is aligned and contiguous. My uneducated intuition is that there’s little regularity as to which pixels will take which branches and will end up requiring which asin calls, but I might be wrong.
I'd expect it to come down to data-oriented design: SoA (structure of arrays) rather than AoS (array of structures).
I skimmed the author's source code, and this is where I'd start: https://github.com/define-private-public/PSRayTracing/blob/8...
Instead of an `_objects`, I might try for a `_spheres`, `_boxes`, etc. (Or just `_lists` still using the virtual dispatch but for each list, rather than each object.) The `asin` seems to be used just for spheres. Within my `Spheres::closest_hit` (note plural), I'd work to SIMDify it. (I'd try to SIMDify the others too of course but apparently not with `asin`.) I think it's doable: https://github.com/define-private-public/PSRayTracing/blob/8...
I don't know much about ray tracers either (having only written a super-naive one back in college) but this is the general technique used to speed up games, I believe. Besides enabling SIMD, it's more cache-efficient and minimizes dispatch overhead.
edit: there's also stuff that you can hoist in this impl. Restructuring as SoA isn't strictly necessary to do that, but it might make it more obvious and natural. As an example, this `ray_dir.length_squared()` is the same for the whole list. You'd notice that when iterating over the spheres. https://github.com/define-private-public/PSRayTracing/blob/8...
When I was working on this project, I was trying to restrict myself to the architecture of the original Ray Tracing in One Weekend book series. I am aware that things are not as SIMD friendly and that becomes a major bottle neck. While I am confident that an architectural change could yield a massive performance boost, it's something I don't want to spend my time on.
I think it's also more fun sometimes to take existing systems and to try to optimize them given whatever constraints exist. I've had to do that a lot in my day job already.
This tracks with my experience and seems reasonable, yes. I tend to SoA all the things, sometimes to my coworkers’ amusement/annoyance.
I don't do much float work but I don't think there is a single regular sine instruction only old x87 float stack ones.
I was curious what "sequence" would end up being but my compiler is too old for that intrinsic. Even godbolt didn't help for gcc or clang but it did reveal that icc produced a call https://godbolt.org/z/a3EsKK4aY
If you click libraries on godbolt, it's pulling in a bunch, including multiple SIMD libraries. You might have to fiddle with the libraries or build locally.
> Nobody likes throwing away work they've done
I like throwing away work I've done. Frees up my mental capacity for other work to throw away.
It appears that the real lesson here was to lean quite a bit more on theory than a programmer's usual roll-your-own heuristic would suggest.
A fantastic amount of collective human thought has been dedicated to function approximations in the last century; Taylor methods are over 200 years old and unlikely to come close to state-of-the-art.
https://bash-org-archive.com/?427792
The 4% improvement doesn't seem like it's worth the effort.
On a general note, instructions like division and square root are roughly equal to trig functions in cycle count on modern CPUs. So, replacing one with the other will not confer much benefit, as evidenced from the results. They're all typically implemented using LUTs, and it's hard to beat the performance of an optimized LUT, which is basically a multiplexer connected to some dedicated memory cells in hardware.
You'd be surprised how it actually is worth the effort, even just a 1% improvement. If you have the time, this is a great talk to listen to: https://www.youtube.com/watch?v=kPR8h4-qZdk
For a little toy ray tracer, it is pretty measly. But for a larger corporation (with a professional project) a 4% speed improvement can mean MASSIVE cost savings.
Some of these tiny improvements can also have a cascading effect. Imagining finding a +4%, a +2% somewhere else, +3% in neighboring code, and a bunch of +1%s here and there. Eventually you'll have built up something that is 15-20% faster. Down the road you'll come across those optimizations which can yield the big results too (e.g. the +25%).
It's a cool talk, but the relevance to the present problem escapes me.
If you're alluding to gcc vs fbstring's performance (circa 15:43), then the performance improvement is not because fbstring is faster/simpler, but due to a foundational gcc design decision to always use the heap for string variables. Also, at around 16:40, the speaker concedes that gcc's simpler size() implementation runs significantly faster (3x faster at 0.3 ns) when the test conditions are different.
> The 4% improvement doesn't seem like it's worth the effort.
People have gotten PhDs for smaller optimizations. I know. I've worked with them.
> instructions like division and square root are roughly equal to trig functions in cycle count on modern CPUs.
What's the x86-64 opcode for arcsin?
Presumably the poster meant polynomial approximations of trigonometric functions not instructions for trigonometric functions, which are missing in most CPUs, though many GPUs have such instructions.
x86-64 had instructions for the exponential and logarithmic functions in Xeon Phi, but those instructions have been removed in Skylake Server and the later Intel or AMD CPUs with AVX-512 support.
However, instructions for trigonometric functions have no longer been added after Intel 80387, and those of 8087 and 80387 are deprecated.
> What's the x86-64 opcode for arcsin?
Not required. ATAN and SQRTS(S|D) are sufficient, the half-angle approach in the article is the recommended way.
> People have gotten PhDs for smaller optimizations. I know. I've worked with them.
I understand the can, not sure about the should. Not trying to be snarky, we just seem to be producing PhDs with the slimmest of justifications. The bar needs to be higher.
> I understand the can, not sure about the should. Not trying to be snarky, we just seem to be producing PhDs with the slimmest of justifications. The bar needs to be higher.
I couldn't disagree more. Sure, making a 4% faster asin isn't going to change the world, but if it makes all callers a teensy bit faster, multiplied by the number of callers using it, then it adds up. Imagine the savings for a hyperscaler if they managed to made a more common instruction 4% faster.
> The 4% improvement doesn't seem like it's worth the effort.
I've spent the past few months improving the performance of some work thing by ~8% and the fun I've been having reminds me of the nineties, when I tried to squeeze every last % of performance out of the 3D graphics engine that I wrote as a hobby.
The effort of typing about 10 words into a LLM is minimal.
Does anyone knows the resources for the algos used in the HW implementations of math functions? I mean the algos inside the CPUs and GPUs. How they make a tradeoff between transistor number, power consumption, cycles, which algos allow this.
Ideal HN content, thanks!
Did some quick calculations, and at this precision, it seems a table lookup might be able to fit in the L1 cache depending on the CPU model.
Microbenchmarks. A LUT will win many of them but you pessimise the rest of the code. So unless a significant (read: 20+%) portion of your code goes into the LUT, there isn't that much point to bother. For almost any pure calculation without I/O, it's better to do the arithmetic than to do memory access.
Locality within the LUT matters too: if you know you're looking up identical or nearby-enough values to benefit from caching, an LUT can be more of a win. You only pay the cache cost for the portion you actually touch at runtime.
I could imagine some graphics workloads tend compute asin() repeatedly with nearby input values. But I'd guess the locality isn't local enough to matter, only eight double precision floats fit in a cache line.
I don’t want to fill up L1 for sin.
Surely the loss in precision of a 32KB LUT for double precision asin() would be unacceptable?
By interpolating between values you can get excellent results with LUTs much smaller than 32KB. Will it be faster than the computation from op, that I don't know.
I experimented a bit with the code. Various tables with different datatypes. There is enough noise from the Monte Carlo to not make a difference if you use smaller data types than double or float. Even dropping interpolation worked fine, and got the speed to be on par with the best in the article, but not faster.
Does your benchmark use sequential or randomly ordered inputs? That would make a substantial difference with an LUT, I would think. But I'm guessing. Maybe 32K is so small it doesn't matter (if almost all of the LUT sits in the cache and is never displaced).
> if you use smaller data types than double or float. Even dropping interpolation worked fine,
That's kinda tautological isn't it? Of course reduced precision is acceptable where reduced precision is acceptable... I guess I'm assuming double precision was used for a good reason, it often isn't :)
I didnt inspect the rest of the code but I guess the table is fetched from L2 on every call? I think the L1 data cache is flooded by other stuff going on all the time.
About dropping the interpolation: Yes you are right of course. I was thinking about the speed. No noticable speed improvement by dropping interpolation. The asin calls are only a small fraction of everything.
I'm very skeptical you wouldn't get perceptible visual artifacts if you rounded the trig functions to 4096 linear approximations. But I'd be happy to be proven wrong :)
Chebyshev approximation for asin is sum(2T_n(x) / (pi*n*n),n), the even terms are 0.
My favorite tool to experiment with math approximation is lolremez. And you can easily ask your llm to do it for you.
If you are interested in such "tricks", you should check out the classic Hacker's Delight by Henry Warren
We love to leave faster functions languishing in library code. The basis for Q3A’s fast inverse square root had been sitting in fdlibm since 1986, on the net since 1993: https://www.netlib.org/fdlibm/e_sqrt.c
Funny enough that fdlimb implementation of asin() did come up in my research. I believe it might have been more performant in the past. But taking a quick scan of `e_asin.c`, I see it doing something similar to the Cg asin() implementation (but with more terms and more multiplications, which my guess is that it's slower). I think I see it also taking more branches (which could also lead to more of a slowdown).
Yeah Ng’s work in fdlibm is cool and really clever in parts but a lot of branching. Some of the ways they reach correct rounding are…so cool.